The Meter4it - Where imagination, appeal, and technology collide, placing you in control.
Promoting the use of turn signals one car at a time!
|
The Meter4it - Where imagination, appeal, and technology collide, placing you in control.
|
|
|
Click on picture for more photos 427 Tunnel Port Engine pictures
Having a 1968 Shelby GT-500 in the family I know how serious you guys are about keeping everything as close to factory as possible. So, I have come up with a Sequential / Chase setup that plugs right into your existing wiring so you don't have to cut any wires. If for some reason you want to take out the unit all you have to do is unplug my unit and plug the original wiring back together. This scores big points at car shows when we are explaining how the system works. Ok you have three different modes to select from: 1968 Shelby Mustang Sequential / Chase turn signal kit
NOTE: If the brakes are applied the brake lights will perform the selected pattern and then all lights will stay on. When brake peddle is released the lights will complete the selected pattern until all are off.
This is what the 1968 Shelby Kit looks like!
Below is a close-up picture showing the "Calibrate button" and the "Jumper" that is used to control the unit. The Red button is used to calibrate the Sequential / Chase unit to your flashers flasher rate. No potentiometers to adjust here! The Blue Jumper with thumb grip is used to select the desired pattern "Sequential", "Chase", or "Factory" |
Sequence selected
|
Chase selected
|
Factory selected
|
| Your baby stays factory. |
|
| You have the reliability of modern technology for your lights |
|
| No one will ever know unless you tell them. |
|
| Your lights will be brighter because the flasher controls 1 light bulb per side and the unit controls the other 2 (per side) via power from courtesy light. |
|
| Easy installation, No wires to cut, dynamite sticks stay wired up but they are not used. |
|
| 20 minutes is all it takes to install the unit and electronic flasher. |
|
| 1 button calibrate, this calibrates the three lights to the flashers flash rate: |
|
| Only one on the market with " Chase " pattern. Selectable via jumper. Sequence, Chase, or All lights together. All in one unit! |
|
| Strong durable plastic casing with mounting flange. Can use double sided tape. |
|
| Only one on the market with one button calibration; As you know every flasher flashes at a different rate. Push one button allow blinkers to cycle three times per side and your done. No potentiometers to adjust! |
|
| Retains calibration even if car battery goes dead. |
|
| Fail safe; if unit fails to operate you still have both inboard lights. Just like if the dynamite sticks stop working you still have both inboard lights. |
|
| Safety; other drivers will notice that something different. |
|
| I'm using 18GA-GXL automotive wire rated for the engine compartment. That's -51 degrees C to +125 degrees C. |
|
| The wire loom is expandable sleeving in Ford blue. This make for a professional looking install. |
|
| The relays are 15 amp rating. Only 15% of the relay is being used under normal operation giving then longer life. |
|
| Unit is not load dependent, you can run LED's or normal filament bulbs. |
|
| Like to rearrange your room? Well I don't, but I do like to make changes to my car. With this one you don't have to pay more to get another option. All you have to do is change a jumper and your done. |
|
| Two year warranty! Just like every one else if unit fails due to no fault of operator I will repair or replace unit minus shipping. |
PLEASE NOTE: The flasher and unit is made to work with the factory light bulbs.
My brother has one on his 68 Shelby and really likes it. His lights are noticeably brighter. He can remove the unit before his car is judged at car shows and then reinstall before he drives back home.
| Description | SKU # | Price |
|---|---|---|
|
1968 Shelby Sequential/ Chase kit with flasher Kit includes wiring harness 5 pin connectors for factory plug and play and modified Electronic flasher (same flasher as below). 2 year warranty. |
Shelby-kit1
| $180 |
|
1968 Shelby Electronic Flasher with wires This is a new Motorcraft electronic flasher that has been modified to work on the 1968 Shelby. This flasher replaces the function of the turn signal flasher and emergency flasher that came factory on the 1968 Shelby. NOTE: Will NOT WORK WITH LED LIGHTS, ONLY FOR FACTORY LIGHT BULBS. |
Shelby-flasher
|
$35
|
| Installation: Currently offered in: Email Wylie, TX Gary | Shelby-install | $35 |
| NOTE: Shipping will be added during checkout. I'm using PayPal to handle transactions. Shipping to other than lower 48 states will be based on your shipping address! |
   
|
